Bearing unit - UCF 205 ASAHI
Unsure if the part fits? Send us the designation, dimensions or a photo.
Send an inquiryRelated products
Product detailed description
UCF 205 ASAHI is a complete flanged bearing unit for a 25 mm shaft. It combines bearing UC205 with cast-iron housing F205 and locks to the shaft using set-screws.
Construction and mating parts
The unit combines a sealed ball bearing with a flanged housing. The bearing's spherical outside surface allows mounting misalignment to be accommodated in the housing seat. This does not permit operation with an arbitrarily deflected shaft: check the alignment of all support positions during installation. When replacing the insert alone, check the lubrication-hole and groove alignment as well as shaft diameter.
The square flange has four fixing holes. L is its side length, J the hole spacing and N the hole diameter.
Dimensions and version selection
- Designation: UCF 205 ASAHI
- Type: Square flanged bearing unit
- Shaft diameter d: 25 mm
- Housing material: Cast iron
- Shaft locking: Set-screws
- Bearing: UC205
- Housing: F205
- Catalogue dimension L: 95 mm
- Catalogue dimension A: 27 mm
- Catalogue dimension J: 70 mm
- Catalogue dimension N: 12 mm
- Catalogue dimension A₁: 14 mm
- Catalogue dimension A₂: 16 mm
- Catalogue dimension A₀: 35.8 mm
- Catalogue dimension B: 34.1 mm
- Catalogue dimension S: 14.3 mm
- Flange mounting bolts: M10
- Catalogue unit mass: 0.72 kg
- Basic dynamic bearing load rating Cr: 14 kN
- Basic static bearing load rating C₀r: 7.9 kN
- Manufacturer set-screw tightening torque: 4.9 N·m
- Set-screw hex key: 3 mm
- Manufacturer grease amount per relubrication: 1.4 g
The listed symbols follow this manufacturer's drawing. Shaft diameter refers to the inner-ring bore, not the outside flange outline. Inner-ring width and overall unit projection are different dimensions. Before replacing a unit, check fixing holes, mounting face, clearance on both sides of the flange and access to the set-screws.
Mounting
Slide the unit onto a clean shaft without impact. Loosened set-screw tips must not project into the bore. Fix the flange to a flat, rigid supporting surface, position the shaft and then secure the inner ring. Set-screws and flange mounting bolts serve different purposes; do not interchange their tightening torques. Check free rotation and proper seating after assembly.
Lubrication and operation
The sealed bearing has a grease reserve and the unit permits relubrication. Select grease and service intervals for speed, temperature and contamination. Catalogue bearing load ratings are not permissible loads for the complete flange or mounting bolts; the entire arrangement must be assessed in the design.
Manufacturer mounting and lubrication data apply to the stated standard version. The relubrication amount is neither the initial bearing fill nor a prescribed maintenance interval.
Additional parameters
| Category: | Bearing housings |
|---|---|
| Weight: | 0.8 kg |
| Designation: | UCF 205 ASAHI |
| Type: | Square flanged bearing unit |
| Shaft diameter d: | 25 mm |
| Housing material: | Cast iron |
| Shaft locking: | Set-screws |
| Bearing: | UC205 |
| Housing: | F205 |
| Catalogue dimension L: | 95 mm |
| Catalogue dimension A: | 27 mm |
| Catalogue dimension J: | 70 mm |
| Catalogue dimension N: | 12 mm |
| Catalogue dimension A₁: | 14 mm |
| Catalogue dimension A₂: | 16 mm |
| Catalogue dimension A₀: | 35.8 mm |
| Catalogue dimension B: | 34.1 mm |
| Catalogue dimension S: | 14.3 mm |
| Flange mounting bolts: | M10 |
| Catalogue unit mass: | 0.72 kg |
| Basic dynamic bearing load rating Cr: | 14 kN |
| Basic static bearing load rating C₀r: | 7.9 kN |
| Manufacturer set-screw tightening torque: | 4.9 N·m |
| Set-screw hex key: | 3 mm |
| Manufacturer grease amount per relubrication: | 1.4 g |
Product rating
Be the first who will post an article to this item!
We can source almost any ASAHI product, even if you cannot find it in our online shop.
Send us the product designation and quantity required. We will check the price, availability and delivery options.
Enquire about ASAHI productsASAHI – Product range and selection
We can help identify the required version of a ASAHI product from the complete designation and available documentation.
Examples from our catalogue
- UK 210 ASAHI
- UCFC 210 ASAHI
- UCT 312 ASAHI
What to include in your enquiry
- The full product designation, including all suffixes and specifications.
- The quantity required and, if relevant, when you need the part.
- Nameplate details, dimensions or a description of the application if the designation is unknown.
You can email a photo or drawing to info@Loziska-Policka.cz.
Your enquiry is non-binding. We will confirm the price, availability and delivery time for the specific product and discuss any alternative with you first.