Bearings
Product sorting
List of products
Bearing - 51112 ZKL
60 × 85 × 17 mm. thrust ball bearing is designed to carry axial load in one direction. It is used where force acting along the shaft axis must be reliably supported.
Bearing - 22312 KJB ZKL
60 × 130 × 46 mm. Double-row spherical roller bearing for high radial loads and axial loads in both directions.
Bearing - 6412 ZKL
60 × 150 × 35 mm. Open deep-groove ball bearing.
Bearing - 22312 KM ZKL
60 × 130 × 46 mm. double-row spherical roller bearing with a 1:12 tapered bore and machined brass cage. For high radial and axial loads in either direction; accommodates angular misalignment.
Bearing - 22312 KW33J ZKL
60 × 130 × 46 mm. double-row spherical roller bearing with a 1:12 tapered bore, W33 lubrication groove and three holes, and a J steel cage. The self-aligning design carries high radial loads together with axial loads in both directions.
Bearing - NJ 2212 E ZVL
60 × 110 × 28 mm. single-row cylindrical roller bearing with high radial load capacity, separable construction and axial guidance in one direction.
Bearing - 6212 2RSR KINEX
60 × 110 × 22 mm. deep-groove ball bearing is a single-row radial bearing with rubber seals on both sides. It carries radial loads and moderate axial forces in either direction. The 2RSR design helps protect the internal rolling contact from dust and moisture while retaining lubricant inside the bearing.
Bearing - 6412A MA C3 ZKL
60 × 150 × 35 mm. Bearing with increased radial internal clearance C3.
Bearing - 6012 SKF
60 × 95 × 18 mm. Deep groove ball bearing is a single-row bearing in an open design. It accommodates radial loads and moderate axial loads in both directions and is suitable for accurate shaft support. The open construction has no integral shields or seals, allowing direct lubricant access but requiring a clean or externally protected environment and a correctly designed lubrication system.
Bearing - 6412 N ZKL
60 × 150 × 35 mm. Single-row deep-groove ball bearing for radial and axial loads in both directions. The N design has a snap-ring groove in the outer ring; when replacing, retain the complete designation and verify the axial locating method.
Bearing - 7212 P6 ZKL
60 × 110 × 22 mm. Higher accuracy class P6 Single-row angular-contact ball bearing for combined radial load and axial load in one direction. P6 accuracy is suitable for arrangements with higher requirements for dimensional and running accuracy.
Bearing - 1212 K ZKL
60 × 110 × 22 mm. ZKL bearing for industrial applications. When replacing a part, always verify the complete designation, dimensions, design and application requirements against the manufacturer documentation.
Bearing - 22212 ZKL
60 × 110 × 28 mm. double-row spherical roller bearing with a cylindrical bore carries high radial loads and axial loads in both directions. Its self-aligning design helps accommodate slight misalignment and shaft deflection.
Bearing - BS2 2212 2CS VT143 HFH
60 × 110 × 34 mm. Technické provedení a kompatibilitu ověřte podle úplného označení výrobce a požadavků aplikace.
Bearing - 6212 N ZVL
60 × 110 × 22 mm. Technické provedení a kompatibilitu ověřte podle úplného označení výrobce a požadavků aplikace.
Bearing - 6212 2RSR ZVL
60 × 110 × 22 mm. Rubber seals on both sides.
Bearing - NU 2212 E XL TVP2 FAG
60 × 110 × 28 mm. FAG bearing with the complete designation. When selecting a replacement, compare the full designation, dimensions and design required for the application.
Bearing - 3312 ZKL
60 × 130 × 54 mm. Technické provedení a kompatibilitu ověřte podle úplného označení výrobce a požadavků aplikace.
Practical advice
How to choose the right bearing
The same dimensions do not necessarily mean the same function. When selecting a replacement, check the construction, cover and seal design, internal clearance, and the conditions in which the bearing will operate.
Determine the type and size
Copy the full type designation. If missing, measure the inner diameter d, outer diameter D and width B.
Check the design
Distinguish open bearing, metal shields, and rubber seals. Also check internal clearance, accuracy, cage, and lubricant.
Take operating conditions into account
Rotational speed, direction, and magnitude of mechanical load, temperature, humidity, dust, and the method of installation are decisive.
How to read the type designation 6204 2RS C3
Suffixes may vary between manufacturers. When replacing, compare technical parameters, not just similar type designation.
Open, 2Z, or 2RS?
When are matching dimensions not enough?
A dimensionally identical bearing may have different load capacity, maximum speed, precision, or internal clearance. Pay special attention to electric motors, high temperatures, vibrations, shocks, and dusty or humid environments.
- radial, axial, and combined loads
- normal or increased internal clearance C3/C4
- operating temperature and maximum speed
- design of shields and seals, lubricant, cage material, and precision
Frequently asked questions
Can I replace a bearing with another brand?
Usually yes, if the design type, dimensions, internal clearance, precision, cover and seal design, load capacity, and allowable speeds match. The basic number alone is not enough; the meaning of the suffixes may vary according to the manufacturer.
How do I determine the diameter of the inner bore from the model designation?
For many common metric bearings, the bore diameter code from 04 is multiplied by five: for example, 04 = 20 mm and 06 = 30 mm. Codes 00 to 03 and some special designs have different rules, so it is advisable to verify the dimension.
Is 2RS better, or 2Z?
Neither is universally better. 2RS usually protects better against dirt and moisture, while 2Z tends to have lower friction and allows higher speeds. The right choice depends on the application.
What to send if the type designation is unreadable?
A photo of both sides, dimensions d × D × B, machine type, and information about speed, load, temperature, humidity, or dustiness. The more operational data we know, the more safely a replacement can be recommended.
Not sure about the replacement?
Send the type designation, dimensions, or a photo of the original part. We will help verify the suitable version before ordering.