Bearings
Product sorting
List of products
Bearing - 22313 W33M ZKL
65 × 140 × 48 mm. bearing with verified mounting dimensions W33M is part of the exact designation; do not substitute a different execution when replacing it.
Bearing - 6213 ZKL
65 × 120 × 23 mm. bearing with clearly stated mounting dimensions. The product name gives no suffix for closure or clearance; compare the complete marking on the original bearing before replacement.
Bearing - 22313 M ZKL
65 × 140 × 48 mm. double-row spherical roller bearing with a solid machined brass cage. Its self-aligning design carries high radial loads, axial loads in both directions and accommodates operating misalignment.
Bearing - 6013 ZKL
65 × 100 × 18 mm. single-row deep-groove ball bearing in an open design. For radial loads and limited axial loads in either direction.
Bearing - 30213 E ZKL
65 × 120 × 24.75 mm. single-row tapered roller bearing for high combined radial and axial loads. Its separable design accommodates axial load in one direction and allows accurate adjustment of clearance or preload during installation.
Bearing - 6013 2RS ZVL
65 × 100 × 18 mm. single-row deep-groove ball bearing with rubber seals on both sides for improved protection of the lubricant and raceways in normally dusty or damp operation.
Bearing - 32313 SKF
65 × 140 × 51 mm. is a robust single-row tapered roller bearing for high combined radial and axial loads. Its separable design simplifies mounting and precise adjustment of clearance or preload.
Bearing - 6313 MP63 ZKL
65 × 140 × 33 mm. deep-groove ball bearing is an open single-row bearing with a solid brass or bronze cage (M), P6 accuracy and greater-than-normal C3 radial clearance (P63). It carries radial loads and axial loads in both directions.
Bearing - 6213 C3 ZVL
65 × 120 × 23 mm. deep-groove ball bearing is an open single-row bearing with greater-than-normal C3 radial internal clearance. It carries radial loads and moderate axial loads in both directions and suits arrangements where interference fits or operating temperatures reduce internal clearance.
Bearing - 6213 2RSR ZVL
65 × 120 × 23 mm. deep-groove ball bearing is a single-row bearing with contact rubber seals on both sides. It carries radial loads and moderate axial loads in both directions, while the factory grease is protected against leakage and common contaminants.
Bearing - 32213 ZKL
65 × 120 × 32.75 mm. Single-row tapered roller bearing for high radial loads and axial load in one direction. The separable outer ring simplifies installation; the correct clearance or preload is set in conjunction with an opposing bearing.
Bearing - 30213 A P6X ZVL
65 × 120 × 24.75 mm. Single-row tapered roller bearing for combined radial load and axial load in one direction. The P6X precision version is intended for arrangements with higher dimensional and running-accuracy requirements; the complete A P6X designation must match the machine documentation.
Bearing - 30213 A ZKL
65 × 120 × 24.75 mm. single-row tapered roller bearing carries high radial load together with axial load in one direction. Its separable inner assembly with rollers and separate outer ring simplify mounting.
Bearing - NN 3013 K P5/C1 ZKL
65 × 100 × 26 mm. Technické provedení a kompatibilitu ověřte podle úplného označení výrobce a požadavků aplikace.
Bearing - 22213 KMW33 NKE
65 × 120 × 31 mm. Bearing for industrial rotating assemblies. Before selecting, verify the full designation, dimensions, and requirements of the specific application.
Bearing - 7313 BECBP SKF
65 × 140 × 33 mm. Technické provedení a kompatibilitu ověřte podle úplného označení výrobce a požadavků aplikace.
Bearing - 51213 A ZKL
65 × 100 × 27 mm. thrust ball bearing is designed to carry axial load in one direction. It is used where force acting along the shaft axis must be reliably supported.
Bearing - 30313 ZKL
ZKL tapered roller bearing for industrial use. Use only when designation, dimensions and design match the original part.
Practical advice
How to choose the right bearing
The same dimensions do not necessarily mean the same function. When selecting a replacement, check the construction, cover and seal design, internal clearance, and the conditions in which the bearing will operate.
Determine the type and size
Copy the full type designation. If missing, measure the inner diameter d, outer diameter D and width B.
Check the design
Distinguish open bearing, metal shields, and rubber seals. Also check internal clearance, accuracy, cage, and lubricant.
Take operating conditions into account
Rotational speed, direction, and magnitude of mechanical load, temperature, humidity, dust, and the method of installation are decisive.
How to read the type designation 6204 2RS C3
Suffixes may vary between manufacturers. When replacing, compare technical parameters, not just similar type designation.
Open, 2Z, or 2RS?
When are matching dimensions not enough?
A dimensionally identical bearing may have different load capacity, maximum speed, precision, or internal clearance. Pay special attention to electric motors, high temperatures, vibrations, shocks, and dusty or humid environments.
- radial, axial, and combined loads
- normal or increased internal clearance C3/C4
- operating temperature and maximum speed
- design of shields and seals, lubricant, cage material, and precision
Frequently asked questions
Can I replace a bearing with another brand?
Usually yes, if the design type, dimensions, internal clearance, precision, cover and seal design, load capacity, and allowable speeds match. The basic number alone is not enough; the meaning of the suffixes may vary according to the manufacturer.
How do I determine the diameter of the inner bore from the model designation?
For many common metric bearings, the bore diameter code from 04 is multiplied by five: for example, 04 = 20 mm and 06 = 30 mm. Codes 00 to 03 and some special designs have different rules, so it is advisable to verify the dimension.
Is 2RS better, or 2Z?
Neither is universally better. 2RS usually protects better against dirt and moisture, while 2Z tends to have lower friction and allows higher speeds. The right choice depends on the application.
What to send if the type designation is unreadable?
A photo of both sides, dimensions d × D × B, machine type, and information about speed, load, temperature, humidity, or dustiness. The more operational data we know, the more safely a replacement can be recommended.
Not sure about the replacement?
Send the type designation, dimensions, or a photo of the original part. We will help verify the suitable version before ordering.