Bearings
Product sorting
List of products
Bearing - 6307 2RS1 SKF
35 × 80 × 21 mm. bearing for replacement use. Before ordering, compare the complete designation and verify the dimensions, design and fit with the original part. Confirm compatibility against SKF documentation and the requirements of the specific application.
Bearing - 6307 ZKL
35 × 80 × 21 mm. single-row deep groove ball bearing in an open design. Deep raceways carry radial and moderate axial loads in both directions with low friction.
Bearing - 6211 2RS C3 SKF
55 × 100 × 21 mm. Single-row deep-groove ball bearing. Rubber seals on both sides; C3 means greater radial internal clearance, so verify suitability.
Bearing - 6307 2RS SKF
35 × 80 × 21 mm. is a single-row deep-groove ball bearing with contact rubber seals on both sides. It supports radial and limited axial loads while protecting the lubricant and raceways in commonly contaminated operation.
Bearing - 6307 2RS ZKL
35 × 80 × 21 mm. single-row deep-groove ball bearing with rubber seals on both sides for reliable operation and protection of the lubricant from contamination.
Bearing - 6307 2RS CX
35 × 80 × 21 mm. Rubber seals on both sides.
Bearing - NJ 307 URB
35 × 80 × 21 mm. single-row cylindrical roller bearing is designed for high radial loads and can also locate the shaft axially in one direction. Its separable construction allows the inner ring to be installed independently of the outer ring and roller assembly.
Bearing - 6307 2RSR KINEX
35 × 80 × 21 mm. single-row deep groove ball bearing with contact rubber seals on both sides. A dependable choice for radial and bidirectional axial loads where retaining lubricant and protecting the bearing interior from contamination are important.
Bearing - 6307 Z ZKL
35 × 80 × 21 mm. deep groove ball bearing has a non-contact metal shield on one side. The shield limits the ingress of larger contaminants and lubricant loss while retaining low friction; the opposite side remains open.
Bearing - 6307 2RS C3 ZKL
35 × 80 × 21 mm. Rubber seals on both sides. Greater radial internal clearance.
Bearing - 6211 2RS ZVL
55 × 100 × 21 mm. Rubber seals on both sides.
Bearing - 2304 ZKL
20 × 52 × 21 mm. Technické provedení a kompatibilitu ověřte podle úplného označení výrobce a požadavků aplikace.
Bearing - 6307 ZC3 ZKL
35 × 80 × 21 mm. Technické provedení a kompatibilitu ověřte podle úplného označení výrobce a požadavků aplikace.
Bearing - 7211 P6 ZKL
55 × 100 × 21 mm. Higher accuracy class P6.
Bearing - NJ 307 ZKL
35 × 80 × 21 mm. Technické provedení a kompatibilitu ověřte podle úplného označení výrobce a požadavků aplikace.
Bearing - 1307 FLT
35 × 80 × 21 mm. FLT bearing for industrial applications. When replacing a part, always verify the complete designation, dimensions, design and application requirements against the manufacturer documentation.
Bearing - 6307 C3 ZKL
35 × 80 × 21 mm. Greater radial internal clearance.
Bearing - 6307 P6 ZKL
35 × 80 × 21 mm. Higher accuracy class P6.
Practical advice
How to choose the right bearing
The same dimensions do not necessarily mean the same function. When selecting a replacement, check the construction, cover and seal design, internal clearance, and the conditions in which the bearing will operate.
Determine the type and size
Copy the full type designation. If missing, measure the inner diameter d, outer diameter D and width B.
Check the design
Distinguish open bearing, metal shields, and rubber seals. Also check internal clearance, accuracy, cage, and lubricant.
Take operating conditions into account
Rotational speed, direction, and magnitude of mechanical load, temperature, humidity, dust, and the method of installation are decisive.
How to read the type designation 6204 2RS C3
Suffixes may vary between manufacturers. When replacing, compare technical parameters, not just similar type designation.
Open, 2Z, or 2RS?
When are matching dimensions not enough?
A dimensionally identical bearing may have different load capacity, maximum speed, precision, or internal clearance. Pay special attention to electric motors, high temperatures, vibrations, shocks, and dusty or humid environments.
- radial, axial, and combined loads
- normal or increased internal clearance C3/C4
- operating temperature and maximum speed
- design of shields and seals, lubricant, cage material, and precision
Frequently asked questions
Can I replace a bearing with another brand?
Usually yes, if the design type, dimensions, internal clearance, precision, cover and seal design, load capacity, and allowable speeds match. The basic number alone is not enough; the meaning of the suffixes may vary according to the manufacturer.
How do I determine the diameter of the inner bore from the model designation?
For many common metric bearings, the bore diameter code from 04 is multiplied by five: for example, 04 = 20 mm and 06 = 30 mm. Codes 00 to 03 and some special designs have different rules, so it is advisable to verify the dimension.
Is 2RS better, or 2Z?
Neither is universally better. 2RS usually protects better against dirt and moisture, while 2Z tends to have lower friction and allows higher speeds. The right choice depends on the application.
What to send if the type designation is unreadable?
A photo of both sides, dimensions d × D × B, machine type, and information about speed, load, temperature, humidity, or dustiness. The more operational data we know, the more safely a replacement can be recommended.
Not sure about the replacement?
Send the type designation, dimensions, or a photo of the original part. We will help verify the suitable version before ordering.