Product sorting
List of products
30x72x27 mm
Double-row self-aligning ball bearing 2306 ZVL
For arrangements with possible angular misalignment; compare the complete designation before ordering.
35x72x27 mm
ZKL double-row angular contact ball bearing for combined radial and axial loads.
30x72x27 mm
ZKL 2306 double-row self-aligning ball bearing for arrangements with minor shaft-to-housing misalignment. Dynamic load rating 32.3 kN, mass 0.50 kg.
50x110x27 mm
The 6310 C 2HRS C3 FAG deep-groove ball bearing is a Generation C single-row bearing with contact seals on both sides and C3 radial internal clearance. It is grease-filled and normally requires no relubrication under suitable operating conditions.
Suitable for motors, pumps, fans, gearboxes and industrial drives requiring contamination protection and additional internal clearance for temperature or tight fits.
6310 2RS C3 ZKL deep-groove ball bearing is a single-row bearing with rubber seals on both sides and greater-than-normal C3 radial internal clearance. It carries radial loads and moderate axial loads in both directions while protecting the factory grease against leakage and common contaminants.
Self-aligning ball bearing 2306 E 2RS1TN9 SKF has two rows of balls and a common spherical raceway in the outer ring. This design accommodates static and dynamic misalignment between the shaft and housing.
Seals on both sides help protect the bearing interior from contaminants. It is suitable for arrangements where shaft deflection or mounting misalignment can occur.
30x72x27 mm
Double-row angular contact ball bearing 3306 CX for combined radial and axial loads in both directions. This stocked item is specified with a width of 27 mm; compare it carefully with the original bearing before replacement.
50x110x27 mm
1310 ZKL double-row self-aligning ball bearing with a cylindrical bore can accommodate slight misalignment between the shaft and housing. The open design is suitable for radial loads and limited axial loads in both directions.
Rubber seals on both sides
65x100x27 mm
ZKL 51213 A thrust ball bearing is designed to carry axial load in one direction. It is used where force acting along the shaft axis must be reliably supported.
50x110x27 mm
Rolling bearing 6310 N ZKL for use in machinery and equipment.
50x110x27 mm
Greater radial internal clearance
Higher accuracy class P6
Single-row deep groove ball bearing 6310 TB P6 C3 FAG
Rubber seals on both sides
Metal shields on both sides
Higher accuracy class P4
Injection moulded cage of glass fibre reinforced polyamide 66
Practical advice
How to choose the right bearing
The same dimensions do not necessarily mean the same function. When selecting a replacement, check the construction, cover and seal design, internal clearance, and the conditions in which the bearing will operate.
Determine the type and size
Copy the full type designation. If missing, measure the inner diameter d, outer diameter D and width B.
Check the design
Distinguish open bearing, metal shields, and rubber seals. Also check internal clearance, accuracy, cage, and lubricant.
Take operating conditions into account
Rotational speed, direction, and magnitude of mechanical load, temperature, humidity, dust, and the method of installation are decisive.
How to read the type designation 6204 2RS C3
Suffixes may vary between manufacturers. When replacing, compare technical parameters, not just similar type designation.
Open, 2Z, or 2RS?
When are matching dimensions not enough?
A dimensionally identical bearing may have different load capacity, maximum speed, precision, or internal clearance. Pay special attention to electric motors, high temperatures, vibrations, shocks, and dusty or humid environments.
- radial, axial, and combined loads
- normal or increased internal clearance C3/C4
- operating temperature and maximum speed
- design of shields and seals, lubricant, cage material, and precision
Frequently asked questions
Can I replace a bearing with another brand?
Usually yes, if the design type, dimensions, internal clearance, precision, cover and seal design, load capacity, and allowable speeds match. The basic number alone is not enough; the meaning of the suffixes may vary according to the manufacturer.
How do I determine the diameter of the inner bore from the model designation?
For many common metric bearings, the bore diameter code from 04 is multiplied by five: for example, 04 = 20 mm and 06 = 30 mm. Codes 00 to 03 and some special designs have different rules, so it is advisable to verify the dimension.
Is 2RS better, or 2Z?
Neither is universally better. 2RS usually protects better against dirt and moisture, while 2Z tends to have lower friction and allows higher speeds. The right choice depends on the application.
What to send if the type designation is unreadable?
A photo of both sides, dimensions d × D × B, machine type, and information about speed, load, temperature, humidity, or dustiness. The more operational data we know, the more safely a replacement can be recommended.
Not sure about the replacement?
Send the type designation, dimensions, or a photo of the original part. We will help verify the suitable version before ordering.