Product sorting
List of products
10x26x8 mm
6000 FLT single-row deep groove ball bearing in open design. A versatile bearing for radial and moderate axial loads in both directions, intended for arrangements providing their own lubrication and contamination protection.
10x26x8 mm
6000 2RS ZVL single-row deep groove ball bearing with contact rubber seals on both sides. A compact solution for radial and moderate axial loads in both directions, protected against dust, contamination and lubricant loss.
10x26x8 mm
6000 2RSH SKF single-row deep groove ball bearing with contact rubber seals on both sides. A compact solution for radial and moderate axial loads in both directions, protected against dust, contamination and lubricant loss.
9x26x8 mm
629 ZKL single-row deep groove ball bearing in an open design. Deep raceways carry radial and moderate axial loads in both directions with low friction.
10x26x8 mm
Single-row 6000 RS ZKL deep-groove ball bearing
Rubber seal on one side; compare the complete designation before ordering.
10x26x8 mm
Single-row 6000 ZR ZKL deep groove ball bearing with a non-contact metal shield on one side. It carries radial and limited axial loads in both directions; the open side provides access to the rolling contact.
9x26x8 mm
629 RS ZKL deep-groove ball bearing with a rubber seal on one side.
10x26x8 mm
SKF 6000 2Z single-row deep-groove ball bearing with non-contact metal shields on both sides. A low-friction shielded design for radial and limited axial loads in both directions.
9x26x8 mm
SKF 629 2Z single-row deep-groove ball bearing with non-contact metal shields on both sides. A compact low-friction design for radial and limited axial loads in both directions.
10x26x8 mm
NTN single-row deep groove ball bearing with non-contact steel shields on both sides, P6 accuracy, C3 radial clearance and electric-motor quality.
10x26x8 mm
KINEX 6000 2RS single-row deep-groove ball bearing with contact rubber seals on both sides. The closed design helps retain lubricant and protects the raceways from contamination and moisture.
17x26x5 mm
Compact KINEX 61803 2RS single-row deep-groove ball bearing with contact rubber seals on both sides.
15x26x12 mm
Radial spherical plain bearing GE 15 ES 2RS SKF with rubber seals on both sides. It accommodates angular movement and misalignment under high radial and combined loads.
10x26x8 mm
6000 Z C6 ZKL is a single-row deep-groove ball bearing with one non-contact metal shield; the opposite side remains open. The design supports radial load and moderate axial loads in both directions while maintaining low friction.
The shield helps retain lubricant and limits the entry of larger contaminants from one side. C6 is part of the complete designation and must be checked against the original bearing or ZKL documentation when selecting a replacement.
629 2RS KINEX deep-groove ball bearing is a single-row bearing with rubber seals on both sides. It carries radial loads and moderate axial loads in both directions while protecting the factory grease against leakage and common contaminants.
6000 2RS1 SKF deep-groove ball bearing is a single-row bearing with rubber seals on both sides. It carries radial loads and moderate axial loads in both directions while protecting the factory grease against leakage and common contaminants.
Deep groove ball bearing 61803 2RS IBB in a slim design with rubber seals on both sides. Suitable for compact arrangements where protection against dust and contamination is important.
Needle roller bearing HK 2012 CX is a thin-walled bearing with a drawn outer cup, cage and needle rollers. Its open-ended design without an inner ring provides high radial load capacity within a very small radial space.
The raceway is normally formed by a hardened and ground shaft surface; when the shaft cannot meet the raceway requirements, a suitable separate inner ring must be used.
Practical advice
How to choose the right bearing
The same dimensions do not necessarily mean the same function. When selecting a replacement, check the construction, cover and seal design, internal clearance, and the conditions in which the bearing will operate.
Determine the type and size
Copy the full type designation. If missing, measure the inner diameter d, outer diameter D and width B.
Check the design
Distinguish open bearing, metal shields, and rubber seals. Also check internal clearance, accuracy, cage, and lubricant.
Take operating conditions into account
Rotational speed, direction, and magnitude of mechanical load, temperature, humidity, dust, and the method of installation are decisive.
How to read the type designation 6204 2RS C3
Suffixes may vary between manufacturers. When replacing, compare technical parameters, not just similar type designation.
Open, 2Z, or 2RS?
When are matching dimensions not enough?
A dimensionally identical bearing may have different load capacity, maximum speed, precision, or internal clearance. Pay special attention to electric motors, high temperatures, vibrations, shocks, and dusty or humid environments.
- radial, axial, and combined loads
- normal or increased internal clearance C3/C4
- operating temperature and maximum speed
- design of shields and seals, lubricant, cage material, and precision
Frequently asked questions
Can I replace a bearing with another brand?
Usually yes, if the design type, dimensions, internal clearance, precision, cover and seal design, load capacity, and allowable speeds match. The basic number alone is not enough; the meaning of the suffixes may vary according to the manufacturer.
How do I determine the diameter of the inner bore from the model designation?
For many common metric bearings, the bore diameter code from 04 is multiplied by five: for example, 04 = 20 mm and 06 = 30 mm. Codes 00 to 03 and some special designs have different rules, so it is advisable to verify the dimension.
Is 2RS better, or 2Z?
Neither is universally better. 2RS usually protects better against dirt and moisture, while 2Z tends to have lower friction and allows higher speeds. The right choice depends on the application.
What to send if the type designation is unreadable?
A photo of both sides, dimensions d × D × B, machine type, and information about speed, load, temperature, humidity, or dustiness. The more operational data we know, the more safely a replacement can be recommended.
Not sure about the replacement?
Send the type designation, dimensions, or a photo of the original part. We will help verify the suitable version before ordering.