Product sorting
List of products
30x55x13 mm
Single-row 6006 2RSR ZVL deep-groove ball bearing
Rubber seals on both sides; compare the complete designation before ordering.
30x55x13 mm
6006 2RS1 SKF single-row deep groove ball bearing with contact rubber seals on both sides. A compact solution for radial and moderate axial loads in both directions, protected against dust, contamination and lubricant loss.
30x55x13 mm
6006 2RS ZVL single-row deep groove ball bearing with contact rubber seals on both sides. It carries radial and moderate axial loads in both directions while protecting the rolling elements from dust, contamination and lubricant loss.
30x55x13 mm
Open single-row 6006 ZKL deep groove ball bearing. It primarily carries radial load and also limited axial loads in both directions; the open design provides direct access for lubrication and requires protection from the surrounding arrangement.
30x55x13 mm
ZKL 6006 2Z single-row deep-groove ball bearing with metal shields on both sides.
For radial loads and limited axial loads in either direction.
30x55x13 mm
ZVL 6006 single-row open deep groove ball bearing for radial and axial loads in both directions. Dynamic load rating 13.24 kN, mass 0.111 kg.
12x55x11
Special neu TR55ZZ HIC0102 bearing with a 12 mm bore, 55 mm outside diameter and 11 mm width. Before ordering, compare the complete designation and the actual shielding design with the original component.
30x55x17 mm
32006 JR DPI is a single-row tapered roller bearing for arrangements exposed to radial load together with axial load in one direction. Its separable design allows the inner ring assembly with cage and rollers to be mounted independently of the outer ring.
It is suitable for gearboxes, hubs, shafts and other precise industrial arrangements. Tapered roller bearings are normally used in opposed pairs when axial forces must be supported in both directions.
Deep groove ball bearing 6006 2Z C3 ZVL is a single-row bearing with metal shields on both sides and C3 radial internal clearance. It accommodates radial loads and moderate axial loads in both directions.
The non-contact 2Z shields limit contaminant ingress while maintaining low friction. C3 clearance is greater than Normal and must suit the temperature, speed and fit; it is not an automatic substitute for standard clearance.
Metal shields on both sides
30x55x13 mm
Single-row deep groove ball bearing 6006 2Z FAG with non-contact metal shields on both sides. Low-friction design for radial and axial loads in both directions; compare the complete 2Z marking before replacement.
35x55x20 mm
NA 4907 DKF needle roller bearing with machined rings and its own inner ring provides high radial load capacity within a small radial section. It is suitable where the shaft surface cannot be used directly as a precision raceway.
Metal shields on both sides
30x55x13 mm
Single-row deep groove ball bearing, sealed on both sides (2RS).
Rubber seals on both sides
35x55x20 mm
SNR bearing for industrial rotating applications. Before ordering, verify the complete designation, dimensions and design against the manufacturer documentation.
Practical advice
How to choose the right bearing
The same dimensions do not necessarily mean the same function. When selecting a replacement, check the construction, cover and seal design, internal clearance, and the conditions in which the bearing will operate.
Determine the type and size
Copy the full type designation. If missing, measure the inner diameter d, outer diameter D and width B.
Check the design
Distinguish open bearing, metal shields, and rubber seals. Also check internal clearance, accuracy, cage, and lubricant.
Take operating conditions into account
Rotational speed, direction, and magnitude of mechanical load, temperature, humidity, dust, and the method of installation are decisive.
How to read the type designation 6204 2RS C3
Suffixes may vary between manufacturers. When replacing, compare technical parameters, not just similar type designation.
Open, 2Z, or 2RS?
When are matching dimensions not enough?
A dimensionally identical bearing may have different load capacity, maximum speed, precision, or internal clearance. Pay special attention to electric motors, high temperatures, vibrations, shocks, and dusty or humid environments.
- radial, axial, and combined loads
- normal or increased internal clearance C3/C4
- operating temperature and maximum speed
- design of shields and seals, lubricant, cage material, and precision
Frequently asked questions
Can I replace a bearing with another brand?
Usually yes, if the design type, dimensions, internal clearance, precision, cover and seal design, load capacity, and allowable speeds match. The basic number alone is not enough; the meaning of the suffixes may vary according to the manufacturer.
How do I determine the diameter of the inner bore from the model designation?
For many common metric bearings, the bore diameter code from 04 is multiplied by five: for example, 04 = 20 mm and 06 = 30 mm. Codes 00 to 03 and some special designs have different rules, so it is advisable to verify the dimension.
Is 2RS better, or 2Z?
Neither is universally better. 2RS usually protects better against dirt and moisture, while 2Z tends to have lower friction and allows higher speeds. The right choice depends on the application.
What to send if the type designation is unreadable?
A photo of both sides, dimensions d × D × B, machine type, and information about speed, load, temperature, humidity, or dustiness. The more operational data we know, the more safely a replacement can be recommended.
Not sure about the replacement?
Send the type designation, dimensions, or a photo of the original part. We will help verify the suitable version before ordering.