Bearings, Page 2

Bearing - 6003 2RSH C3 SKF

17 × 35 × 10 mm. SKF 6003-2RSH/C3 single-row deep groove ball bearing with greater C3 radial internal clearance and NBR contact seals on both sides. It is grease filled and protected against contamination.

Bearing - 6003 RS ZKL

17 × 35 × 10 mm. Single-row ZKL 6003-RS deep groove ball bearing with a rubber seal on one side. The sealed side helps protect the lubricant, while the opposite side remains open for the lubrication method defined by the bearing arrangement.

Bearing - 6202 FLT

15 × 35 × 11 mm. Open single-row deep-groove ball bearing for reliable radial and limited axial load carrying. Its versatile non-separable design suits a wide range of machinery applications.

Bearing - 6003 C3 ZKL

17 × 35 × 10 mm. is an open single-row deep-groove ball bearing with greater-than-normal C3 radial internal clearance. It suits radial and limited axial loads where operating conditions require additional internal clearance.

Bearing - 6003 2Z ZVL

17 × 35 × 10 mm. is a single-row deep-groove ball bearing with two non-contact metal shields. Its versatile design supports radial load and moderate axial loads in both directions, while low friction makes it suitable for higher speeds. The shields help retain lubricant and limit the entry of larger contaminants. This is a general-purpose machine bearing, not a contact-sealed or watertight design.

Bearing - 6300 ZKL

10 × 35 × 11 mm. is an open, single-row deep-groove ball bearing. It supports radial load and moderate axial loads in both directions, while its low-friction design makes it suitable for higher speeds. The open design has no shields or seals, allowing easy lubricant access and effective heat dissipation. It therefore requires a clean arrangement with suitable lubrication or external sealing.

Bearing - 6202 2RS SS CX

15 × 35 × 11 mm. is a stainless-steel single-row deep-groove ball bearing with contact seals on both sides. The seals help retain lubricant and protect the rolling space from dust, moisture and common contaminants. The stainless-steel design provides improved corrosion resistance compared with standard bearing steel. Suitability for a specific chemical environment, temperature or water exposure must be….

Bearing - 6003 2RSH SKF

17 × 35 × 10 mm. single-row deep-groove ball bearing with high-performance contact seals on both sides for reliable protection of the lubricant and bearing interior.

Bearing - 6003 2Z ZKL

17 × 35 × 10 mm. single-row deep-groove ball bearing with metal shields on both sides for lubricant protection and low friction.

Bearing - 6003 2RS FAG

17 × 35 × 10 mm. deep-groove ball bearing is a single-row radial bearing with rubber seals on both sides. It carries radial loads and moderate axial forces in either direction. The 2RS design helps protect the internal rolling contact from dust and moisture while retaining lubricant inside the bearing.

Bearing - 6003 2RS MGK

17 × 35 × 10 mm. Single-row deep-groove ball bearing with rubber seals on both sides. Check the complete designation and suitability for the specific application.

Bearing - 1202 KINEX

15 × 35 × 11 mm. bearing with the verified designation. Compare the complete designation, dimensional data and design with the original part. Confirm suitability for the specific bearing arrangement in KINEX documentation.  

Bearing - 51203 P6 ZKL

17 × 35 × 12 mm. thrust ball bearing is designed to carry axial load in one direction. It is used where force acting along the shaft axis must be reliably supported.

Bearing - 6202 C 2HRS FAG

15 × 35 × 11 mm. Technické provedení a kompatibilitu ověřte podle úplného označení výrobce a požadavků aplikace.

Bearing - 51104 FAG

20 × 35 × 10 mm. thrust ball bearing is designed to carry axial load in one direction. It is used where force acting along the shaft axis must be reliably supported.