Bearings
Product sorting
List of products
Bearing - 608 2Z NMB
8 × 22 × 7 mm. Single-row deep-groove ball bearing. Metal shields on both sides; compare the complete designation before ordering.
Bearing - 608 2Z SKF
8 × 22 × 7 mm. Single-row SKF bearing with non-contact metal shields on both sides (2Z) and normal radial clearance CN. Check the complete designation before ordering.
Bearing - 608 Z ZKL
8 × 22 × 7 mm. Single-row deep-groove ball bearing with a non-contact metal shield on one side (Z). Check the complete designation and application suitability.
Bearing - 608 2RS ZKL
8 × 22 × 7 mm. Single-row deep-groove ball bearing with contact rubber seals on both sides (2RS). Verify the complete designation before ordering.
Bearing - 608 2RSH SKF
8 × 22 × 7 mm. Single-row deep-groove ball bearing. Contact seals of synthetic rubber (NBR) on both sides; compare the 2RSH suffix.
Bearing - 698 2Z P5 ZEN
8 × 19 × 6 mm. single-row deep groove ball bearing in P5 precision class, with non-contact metal shields on both sides. Suitable for radial and moderate axial loads in both directions, combining low friction with protection of the lubricant from larger contaminants.
Bearing - 608 2Z FBJ
8 × 22 × 7 mm. deep-groove ball bearing with metal shields on both sides.
Bearing - 608 ZKL
8 × 22 × 7 mm. single-row deep groove ball bearing in open design. A compact bearing for radial and moderate axial loads in both directions, intended for arrangements providing their own lubrication and protection.
Bearing - 608 2RS TIMKEN
8 × 22 × 7 mm. single-row deep groove ball bearing with contact rubber seals on both sides. It carries radial and moderate axial loads in both directions while protecting the rolling elements from dust, contamination and lubricant loss.
Bearing - S 688 2Z GPR J GRW
8 × 16 × 5 mm. stainless-steel single-row deep-groove ball bearing with metal shields on both sides. Compact design for radial loads and light axial loads in both directions.
Bearing - 628 NACHI
8 × 24 × 8 mm. Open single-row 628 deep-groove ball bearing for accurate support of small shafts and rotating mechanisms. It carries radial load and limited axial load in both directions.
Bearing - 608 2Z C3 INA
8 × 22 × 7 mm. single-row deep-groove ball bearing with non-contact metal shields on both sides. A low-friction shielded design for radial and limited axial loads in both directions. The C3 suffix denotes greater-than-normal radial internal clearance.
Bearing - EL 8 SKF
8 × 22 × 7 mm. Legacy designation for a single-row deep-groove ball bearing in the 608 dimensional series; verify the actual closure and clearance markings.
Bearing - 628 2Z ZKL
8 × 24 × 8 mm. single-row deep-groove ball bearing with non-contact metal shields on both sides for low friction and protection from ordinary contamination.
Bearing - 638 2RS KBS
8 × 28 × 9 mm. single-row deep-groove ball bearing with rubber seals on both sides for improved protection of the lubricant and raceways in normally dusty or damp operation.
Bearing - 608 ZC4 ZKL
8 × 22 × 7 mm. is a single-row deep-groove ball bearing with one Z metal shield and very large C4 radial internal clearance. Its compact design supports radial and limited axial loads in both directions.
Bearing - 688 2Z RMB
8 × 16 × 5 mm. Miniature thin-section deep groove ball bearing with metal shields on both sides. Its highly compact design provides low friction and protection for precise small mechanisms.
Needle roller bearing - HK 0810 SKF
8 × 12 × 10 mm. is a drawn-cup needle roller bearing with open ends. Its compact cross-section provides high radial load carrying capacity and stiffness; it is not intended to support axial load. The bearing has no separate inner ring, so a suitably hardened and ground shaft surface normally forms the raceway. Correct shaft quality, housing fit and lubrication are essential for service life.
Practical advice
How to choose the right bearing
The same dimensions do not necessarily mean the same function. When selecting a replacement, check the construction, cover and seal design, internal clearance, and the conditions in which the bearing will operate.
Determine the type and size
Copy the full type designation. If missing, measure the inner diameter d, outer diameter D and width B.
Check the design
Distinguish open bearing, metal shields, and rubber seals. Also check internal clearance, accuracy, cage, and lubricant.
Take operating conditions into account
Rotational speed, direction, and magnitude of mechanical load, temperature, humidity, dust, and the method of installation are decisive.
How to read the type designation 6204 2RS C3
Suffixes may vary between manufacturers. When replacing, compare technical parameters, not just similar type designation.
Open, 2Z, or 2RS?
When are matching dimensions not enough?
A dimensionally identical bearing may have different load capacity, maximum speed, precision, or internal clearance. Pay special attention to electric motors, high temperatures, vibrations, shocks, and dusty or humid environments.
- radial, axial, and combined loads
- normal or increased internal clearance C3/C4
- operating temperature and maximum speed
- design of shields and seals, lubricant, cage material, and precision
Frequently asked questions
Can I replace a bearing with another brand?
Usually yes, if the design type, dimensions, internal clearance, precision, cover and seal design, load capacity, and allowable speeds match. The basic number alone is not enough; the meaning of the suffixes may vary according to the manufacturer.
How do I determine the diameter of the inner bore from the model designation?
For many common metric bearings, the bore diameter code from 04 is multiplied by five: for example, 04 = 20 mm and 06 = 30 mm. Codes 00 to 03 and some special designs have different rules, so it is advisable to verify the dimension.
Is 2RS better, or 2Z?
Neither is universally better. 2RS usually protects better against dirt and moisture, while 2Z tends to have lower friction and allows higher speeds. The right choice depends on the application.
What to send if the type designation is unreadable?
A photo of both sides, dimensions d × D × B, machine type, and information about speed, load, temperature, humidity, or dustiness. The more operational data we know, the more safely a replacement can be recommended.
Not sure about the replacement?
Send the type designation, dimensions, or a photo of the original part. We will help verify the suitable version before ordering.