Product sorting
List of products
10x30x9 mm
6200 RS ZKL single-row deep groove ball bearing with a contact rubber seal on one side. Suitable for radial and moderate axial loads in both directions when one side needs protection from dust, contamination and lubricant loss.
10x30x9 mm
6200 2Z SKF single-row deep groove ball bearing with non-contact metal shields on both sides. Suitable for radial and moderate axial loads in both directions, combining low friction with protection of the lubricant from larger contaminants.
10x30x9 mm
6200 Z ZKL single-row deep groove ball bearing with a non-contact metal shield on one side. Suitable for radial and moderate axial loads in both directions when one side of the bearing needs protection from coarse contamination.
10x30x9 mm
6200 2RS CRAFT single-row deep groove ball bearing with contact rubber seals on both sides. It carries radial and moderate axial loads in both directions while protecting the rolling elements from dust, contamination and lubricant loss.
10x30x9 mm
6200 2Z MSC deep-groove ball bearing with metal shields on both sides.
17x30x7 mm
Rubber seals on both sides. Thin-section ZVL single-row deep groove ball bearing for installations with limited radial space.
10x30x9 mm
SKF 6200 2RS single-row deep-groove ball bearing with rubber seals on both sides.
For radial loads and limited axial loads in either direction.
10x30x9 mm
6200 2RS ZVL is a single-row deep-groove ball bearing with contact rubber seals on both sides. It supports radial and limited axial loads while protecting the lubricant and raceways in commonly contaminated operation.
10x30x14 mm
Double-row self-aligning ball bearing 2200 E-2RS1TN9 SKF with seals on both sides. It accommodates static and dynamic misalignment and supports reliable operation in compact bearing arrangements.
10x30x9 mm
6200 2Z DPI is a single-row deep-groove ball bearing with two non-contact metal shields. It supports radial load and moderate axial loads in both directions, while its low-friction design makes it suitable for higher speeds.
The shields help retain lubricant and limit the entry of larger contaminants. This is a general-purpose machine bearing, not a contact-sealed or watertight design.
61903 2RS1 SKF deep-groove ball bearing is a single-row bearing with contact rubber seals on both sides. It carries radial loads and moderate axial loads in both directions, while the factory grease is protected against leakage and common contaminants.
Dimensions: 10 × 30 × 9 mm
Deep groove ball bearing, shielded on both sides (2Z).
10x30x9 mm
SKF bearing with the complete designation 6200 Z SKF. When selecting a replacement, compare the full designation, dimensions and design required for the application.
10x30x9 mm
Higher accuracy class P4
Rolling bearing 7200 CBTB P4 ZKL
17x30x9 mm
ZVL 51103 thrust ball bearing is designed to carry axial load in one direction. It is used where force acting along the shaft axis must be reliably supported.
Rubber seals on both sides
10x30x9 mm
Deep groove ball bearing, shielded on both sides (2Z).
Metal shields on both sides
Practical advice
How to choose the right bearing
The same dimensions do not necessarily mean the same function. When selecting a replacement, check the construction, cover and seal design, internal clearance, and the conditions in which the bearing will operate.
Determine the type and size
Copy the full type designation. If missing, measure the inner diameter d, outer diameter D and width B.
Check the design
Distinguish open bearing, metal shields, and rubber seals. Also check internal clearance, accuracy, cage, and lubricant.
Take operating conditions into account
Rotational speed, direction, and magnitude of mechanical load, temperature, humidity, dust, and the method of installation are decisive.
How to read the type designation 6204 2RS C3
Suffixes may vary between manufacturers. When replacing, compare technical parameters, not just similar type designation.
Open, 2Z, or 2RS?
When are matching dimensions not enough?
A dimensionally identical bearing may have different load capacity, maximum speed, precision, or internal clearance. Pay special attention to electric motors, high temperatures, vibrations, shocks, and dusty or humid environments.
- radial, axial, and combined loads
- normal or increased internal clearance C3/C4
- operating temperature and maximum speed
- design of shields and seals, lubricant, cage material, and precision
Frequently asked questions
Can I replace a bearing with another brand?
Usually yes, if the design type, dimensions, internal clearance, precision, cover and seal design, load capacity, and allowable speeds match. The basic number alone is not enough; the meaning of the suffixes may vary according to the manufacturer.
How do I determine the diameter of the inner bore from the model designation?
For many common metric bearings, the bore diameter code from 04 is multiplied by five: for example, 04 = 20 mm and 06 = 30 mm. Codes 00 to 03 and some special designs have different rules, so it is advisable to verify the dimension.
Is 2RS better, or 2Z?
Neither is universally better. 2RS usually protects better against dirt and moisture, while 2Z tends to have lower friction and allows higher speeds. The right choice depends on the application.
What to send if the type designation is unreadable?
A photo of both sides, dimensions d × D × B, machine type, and information about speed, load, temperature, humidity, or dustiness. The more operational data we know, the more safely a replacement can be recommended.
Not sure about the replacement?
Send the type designation, dimensions, or a photo of the original part. We will help verify the suitable version before ordering.