Bearings, Page 2

30x72x19 mm

6306 2Z TIMKEN is a single-row deep-groove ball bearing with two non-contact metal shields. Its versatile design supports radial load and moderate axial loads in both directions, while low friction makes it suitable for higher speeds.

The shields help retain lubricant and limit the entry of larger contaminants. This is a general-purpose machine bearing, not a contact-sealed or watertight design.

35x72x17 mm

NJ 207 ZKL cylindrical roller bearing is a single-row radial bearing with high load capacity and rigidity. The NJ design has two guiding flanges on the outer ring and one on the inner ring, allowing it to carry radial load, locate the shaft axially in one direction and permit axial displacement in the opposite direction.

35x72x17 mm

6207 2Z ZKL deep-groove ball bearing is a single-row radial bearing with non-contact metal shields on both sides. It supports radial loading and moderate axial forces in either direction. The 2Z shields help retain lubricant and keep out coarse contaminants while maintaining low friction and suitability for higher speeds.

30x72x19 mm

6306 2RS ZVL deep-groove ball bearing is a single-row radial bearing with rubber seals on both sides. It carries radial loads and moderate axial forces in either direction. The 2RS design helps protect the internal rolling contact from dust and moisture while retaining lubricant inside the bearing.

35x72x42.9 mm

The UC 207 DKF insert bearing is a sealed ball-bearing insert with a spherical outside surface and an extended inner ring. It is secured to the shaft by two grub screws and is designed for installation in a matching bearing housing.

Suitable for conveyors, fans, agricultural machinery and simple industrial drives. This product is the UC insert only; a complete housing is not included.

32207 A ZKL tapered roller bearing is a separable single-row bearing for high radial loads combined with axial load in one direction. The A design offers increased load capacity and a higher limiting speed; clearance or preload is established during installation.

Self-aligning ball bearing 2306 E 2RS1TN9 SKF has two rows of balls and a common spherical raceway in the outer ring. This design accommodates static and dynamic misalignment between the shaft and housing.

Seals on both sides help protect the bearing interior from contaminants. It is suitable for arrangements where shaft deflection or mounting misalignment can occur.

Cylindrical roller bearing NU 306 ZKL is a single-row radial bearing with high load capacity. The NU design has two integral flanges on the outer ring and an inner ring without flanges.

It permits axial displacement of the shaft relative to the housing in both directions and is therefore primarily used as a non-locating bearing. It does not provide axial shaft location.

30x72x19 mm

Single-row cylindrical roller bearing NJ 306 FRB for high radial loads and axial location in one direction. The NJ design permits axial displacement of the shaft relative to the housing in the opposite direction; when replacing, compare the complete designation and required internal clearance.

35x72x17 mm

Single-row cylindrical roller bearing N 207 ZKL for high radial loads and accurate shaft guidance. The N design permits axial displacement of the shaft relative to the housing in both directions; when replacing, compare the complete designation and required internal clearance.

35x72x17 mm

Single-row deep-groove ball bearing 6207 N ZKL for radial and axial loads in both directions. The N design has a snap-ring groove in the outer ring; when replacing, retain the complete designation and verify the axial locating method.

35x72x42.9 mm

Radial insert ball bearing GYE 35 KRR B INA with a spherical outside surface, extended inner ring and locking by grub screws. Seals on both sides protect the rolling contact; the bearing is designed for installation in a matching bearing housing.

35x72x23 mm

Double-row self-aligning ball bearing 2207 ZKL with a cylindrical bore. The spherical outer-ring raceway accommodates angular misalignment; suitable primarily for radial load and limited axial load in both directions.

35x72x17 mm

Double-row self-aligning ball bearing 1207 K ZKL with a 1:12 tapered bore. It accommodates slight misalignment and shaft deflection while carrying radial loads and light axial loads in both directions.

30x72x27 mm

Double-row angular contact ball bearing 3306 CX for combined radial and axial loads in both directions. This stocked item is specified with a width of 27 mm; compare it carefully with the original bearing before replacement.

35x72x17 mm

6207 RS ZKL single-row deep groove ball bearing with a contact rubber seal on one side. Suitable for radial and moderate axial loads in both directions when one side requires improved protection from dust, contamination and lubricant loss.