Bearings, Page 20

Bearing - HR 30207 J NSK

35 × 72 × 18.25 mm. Single-row tapered roller bearing for combined radial and one-direction axial loads. Its precise separable construction provides high rigidity and permits adjustment of bearing clearance or preload.

Bearing - 625 2Z RMB

5 × 16 × 5 mm. Miniature single-row deep groove ball bearing with metal shields on both sides. Its compact, low-friction design protects against common contaminants and supports reliable operation in small mechanisms.

Bearing - KLNJ 1/2 C RHP

12.7 × 28.575 × 6.35 mm. Imperial single-row deep groove ball bearing. Its compact open design supports low friction together with radial and moderate axial loads.

Bearing - 6906 ZZ IBB

30 × 47 × 9 mm. Thin-section single-row deep groove ball bearing with metal shields on both sides. Its compact cross-section, low friction and two-sided protection suit space-constrained rotating arrangements.

Bearing - KH 2030 PP INA

20 × 28 × 30 mm. Compact linear ball bearing for accurate linear motion on a 20 mm shaft. Wiper seals at both ends help retain lubricant and limit contaminant ingress.

Bearing - 688 2Z RMB

8 × 16 × 5 mm. Miniature thin-section deep groove ball bearing with metal shields on both sides. Its highly compact design provides low friction and protection for precise small mechanisms.

Bearing - 32006 JR DPI

30 × 55 × 17 mm. is a single-row tapered roller bearing for arrangements exposed to radial load together with axial load in one direction. Its separable design allows the inner ring assembly with cage and rollers to be mounted independently of the outer ring. It is suitable for gearboxes, hubs, shafts and other precise industrial arrangements. Tapered roller bearings are normally used in opposed pairs when….

Bearing - 1209 MGM

45 × 85 × 19 mm. MGM bearing for industrial applications. When replacing a part, always verify the complete designation, dimensions, design and application requirements against the manufacturer documentation.

Bearing - 6305 2ZR FAG

25 × 62 × 17 mm. is a single-row deep-groove ball bearing with two non-contact metal shields. Its versatile design supports radial load and moderate axial loads in both directions, while low friction makes it suitable for higher speeds. The shields help retain lubricant and limit the entry of larger contaminants. This is a general-purpose machine bearing, not a contact-sealed or watertight design.

Bearing - 6304 2RSH SKF

20 × 52 × 15 mm. is a single-row deep-groove ball bearing with contact seals on both sides. The seals help retain lubricant and protect the rolling space from dust, moisture and other common contaminants. Its versatile design supports radial load and moderate axial loads in both directions. It is well suited to applications where dependable bearing protection and low maintenance requirements are important.

Bearing - NA 40 V ZKL

40 × 65 × 22 mm. is a full-complement needle roller bearing with an inner ring, dimensionally corresponding to type NKIS40. The V design uses a full complement of needles without a cage, providing high radial load capacity in a compact cross-section. It is intended primarily for high radial loads at low to moderate speeds. The separate inner ring also permits use where the shaft cannot be prepared as a….

Bearing - 6306 2Z TIMKEN

30 × 72 × 19 mm. is a single-row deep-groove ball bearing with two non-contact metal shields. Its versatile design supports radial load and moderate axial loads in both directions, while low friction makes it suitable for higher speeds. The shields help retain lubricant and limit the entry of larger contaminants. This is a general-purpose machine bearing, not a contact-sealed or watertight design.

Bearing - 6007 2RS1 SKF

35 × 62 × 14 mm. Rubber seals on both sides.

Bearing - 6305 2RSR FAG

25 × 62 × 17 mm. is a single-row deep-groove ball bearing with contact seals on both sides. The seals help retain lubricant and protect the rolling space from dust, moisture and other common contaminants. Its versatile design supports radial load and moderate axial loads in both directions. It is well suited to applications where dependable bearing protection and low maintenance requirements are important.

Bearing - 6005 FAG

25 × 47 × 12 mm. is an open, single-row deep-groove ball bearing. It supports radial load and moderate axial loads in both directions, while its low-friction design makes it suitable for higher speeds. The open design has no shields or seals, allowing easy lubricant access and effective heat dissipation. It therefore requires a clean arrangement with suitable lubrication or external sealing.