Product sorting
List of products
12x28x8 mm
6001 2RS ZVL single-row deep groove ball bearing with contact rubber seals on both sides. A compact solution for radial and moderate axial loads in both directions, protected against dust, contamination and lubricant loss.
12x28x8 mm
Single-row 6001 2RS KINEX deep-groove ball bearing
Rubber seals on both sides; compare the complete designation before ordering.
12x28x8 mm
6001 2RS SKF single-row deep groove ball bearing with contact rubber seals on both sides. A compact solution for radial and moderate axial loads in both directions, protected against dust, contamination and lubricant loss.
12x28x8 mm
6001 2Z SKF single-row deep groove ball bearing with non-contact metal shields on both sides. It combines low friction and lubricant retention with the ability to carry radial and moderate axial loads in both directions.
12x28x8 mm
Metal shield on one side. ZKL single-row deep groove ball bearing for compact rotating assemblies.
12x28x8 mm
URB 6001 single-row open deep groove ball bearing for radial and axial loads in both directions. Dynamic load rating 5.1 kN, mass 0.022 kg.
15x28x7 mm
Compact KINEX 61902 2RS single-row deep-groove ball bearing with contact rubber seals on both sides.
8x28x9 mm
KBS 638 2RS single-row deep-groove ball bearing with rubber seals on both sides for improved protection of the lubricant and raceways in normally dusty or damp operation.
12x28x8 mm
Single-row deep groove ball bearing 6001 ZKL for common radial and moderate axial loads. Its versatile open design provides low friction, smooth running and straightforward relubrication.
15x28x7 mm
6902 2RS DPI thin-section deep-groove ball bearing with rubber seals on both sides for compact arrangements and protection of the lubricant from contamination.
S 6001 2RS neu deep-groove ball bearing is a single-row bearing with contact rubber seals on both sides. It carries radial loads and moderate axial loads in both directions, while the factory grease is protected against leakage and common contaminants.
Deep groove ball bearing SS 6001 2RS CRB is a compact single-row 6001-series bearing with rubber seals on both sides. It is suitable for shaft arrangements carrying radial and moderate axial loads.
The double-sealed design helps protect the bearing interior from common contaminants. Before ordering, compare the complete designation, dimensions and operating requirements; the SS prefix is part of this specific variant designation.
12x28x11 mm
URB 51201 thrust ball bearing is designed to carry axial load in one direction. It is used where force acting along the shaft axis must be reliably supported.
15x28x9 mm
URB 51102 thrust ball bearing is designed to carry axial load in one direction. It is used where force acting along the shaft axis must be reliably supported.
Rubber seals on both sides
12x28x8 mm
NEU bearing for industrial applications. When replacing a part, always verify the complete designation, dimensions, design and application requirements against the manufacturer documentation.
12x28x8 mm
CX bearing for industrial applications. When replacing a part, always verify the complete designation, dimensions, design and application requirements against the manufacturer documentation.
Rubber seals on both sides
Practical advice
How to choose the right bearing
The same dimensions do not necessarily mean the same function. When selecting a replacement, check the construction, cover and seal design, internal clearance, and the conditions in which the bearing will operate.
Determine the type and size
Copy the full type designation. If missing, measure the inner diameter d, outer diameter D and width B.
Check the design
Distinguish open bearing, metal shields, and rubber seals. Also check internal clearance, accuracy, cage, and lubricant.
Take operating conditions into account
Rotational speed, direction, and magnitude of mechanical load, temperature, humidity, dust, and the method of installation are decisive.
How to read the type designation 6204 2RS C3
Suffixes may vary between manufacturers. When replacing, compare technical parameters, not just similar type designation.
Open, 2Z, or 2RS?
When are matching dimensions not enough?
A dimensionally identical bearing may have different load capacity, maximum speed, precision, or internal clearance. Pay special attention to electric motors, high temperatures, vibrations, shocks, and dusty or humid environments.
- radial, axial, and combined loads
- normal or increased internal clearance C3/C4
- operating temperature and maximum speed
- design of shields and seals, lubricant, cage material, and precision
Frequently asked questions
Can I replace a bearing with another brand?
Usually yes, if the design type, dimensions, internal clearance, precision, cover and seal design, load capacity, and allowable speeds match. The basic number alone is not enough; the meaning of the suffixes may vary according to the manufacturer.
How do I determine the diameter of the inner bore from the model designation?
For many common metric bearings, the bore diameter code from 04 is multiplied by five: for example, 04 = 20 mm and 06 = 30 mm. Codes 00 to 03 and some special designs have different rules, so it is advisable to verify the dimension.
Is 2RS better, or 2Z?
Neither is universally better. 2RS usually protects better against dirt and moisture, while 2Z tends to have lower friction and allows higher speeds. The right choice depends on the application.
What to send if the type designation is unreadable?
A photo of both sides, dimensions d × D × B, machine type, and information about speed, load, temperature, humidity, or dustiness. The more operational data we know, the more safely a replacement can be recommended.
Not sure about the replacement?
Send the type designation, dimensions, or a photo of the original part. We will help verify the suitable version before ordering.